Creation of diamonds out of black sea salt while CO2 Gans production.

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Creation of diamonds out of black sea salt while CO2 Gans production.

    I have applied the method of Arvis Liepa by using a graphite plate instead of a nc copper plate. Additionally I chose black sea salt in distilled water which contains one weight % of activated volcanic charcoal. I ran the CO2 Gans production with two Zinc plates (connected to minus) in parallel. The carbon plate (connected to +1.5V at 0.5 A) was placed in between the Zinc plates. After running the set up for 12h I saw the expected CO2 Gans but also a very shiny surface on top of the carbon plate. I first thought of tiny gas bubbles but after getting out the graphite plate I could see tiny translucent crystals on the top(diamonds?). I guess those were grown from the charcoal particles in the water. Maybe one could repeat this process to check it out again. While the process took place the current dropped from 0.5 A to 0.37 A.

  • #2
    Originally posted by marcel00 View Post
    I have applied the method of Arvis Liepa by using a graphite plate instead of a nc copper plate. Additionally I chose black sea salt in distilled water which contains one weight % of activated volcanic charcoal. I ran the CO2 Gans production with two Zinc plates (connected to minus) in parallel.
    ...
    I did the same, but only with spring water... http://www.bar-le-duc.nl/

    ...NO salt







    C also
    http://forum.keshefoundation.org/for...4230#post54230


    using 24Volts, 220Ohms, @25mA, for about 8 to 10 hours

    To awaken you need do nothing! Just be yourselves, that is allow the Love that is your true and eternal nature to flow freely through you to everyone with whom you interact in any way. You all want only Love, you spend lifetimes searching for It outside yourselves inside the illusion, inside other seemingly separate individuals and all the time, throughout every one of your human life experiences, It has resided within you waiting for you to notice Its Flame burning gently, constantly, and eternally, calling you to awaken.
    https://johnsmallman2.wordpress.com/...-ever-present/
    GRAphi
    https://en.wikipedia.org/wiki/Graphite
    https://en.wikipedia.org/wiki/Phi


    https://en.wikipedia.org/wiki/Lozenge

    1500-10; < Latin gravitāt- (stem of gravitās) heaviness, equivalent to grav
    http://www.dictionary.com/browse/gravity

    heaviness
    https://www.youtube.com/watch?v=nREV8bQJ1MA
    HEAVEN

    GRAV
    https://en.wikipedia.org/wiki/Grave

    https://en.wikipedia.org/wiki/Gravitation_(M._C._Escher)



    Magnificent people
    http://mashable.com/2016/07/01/alber...k#Xe2P2QKXhkqW



    Gardens Flower Beauty
    https://www.facebook.com/profile.php...5667128&type=3
    .
    Last edited by science2art; July 6th, 2016, 10:50 AM.

    Comment


    • #3
      Hello, this is very interesting,
      has you used an air pump bubler in the cofiguration?could be the salt crystals?

      Comment


      • #4
        In the method of Arvis Liepa the negative pole is conected to the carbon stick and the positive to the metal plate,
        did you connect the battery this way or you conected the negative to metal, and the positive to carbon stick?

        Comment


        • #5
          Hello Mokete. I did not use an air pump. If it were salt crystals they would have been dissolved in the water again. This is not the case. At first I had the carbon plate connected to negative. In that case I smelled a gas similar to hazardous chlorine. Most probably due to separation of sodium chloride. The CO2 +ZnO production was taking place but than I changed the polarity and the current significantly increased at the same voltage. So I lowered the voltage from 6 to 1.3V for obtaining around 0.5 A again. The production of CO2 gans becomes more efficient and not only because of less power consumption. The amorphous carbon plate on positive attracs the charcoal nanoparticles which start to grow a chrystal structure on the plate.

          Comment


          • #6
            i dont know, making good co2 gans is so easy, why so much discussion.
            See the result after 12 hour.

            0,5 l jar
            400m,l dest. water
            40gr seawater salt
            pc. zinc sheet
            pc. coatet copper sheet
            no crocodile clamps, only copper cable

            leave it, it works fine ( in my environment ( the environment is very importent, should be harmoniously)

            Comment


            • #7
              hello, i configured it first with the positive to carbon, and nothing happens, then i change the negative pole to carbon and gans production began, and can see rhe carbon bubling, then now that there is gans production runing i change the pole, positive to carbon, and it appears to stop, can't hear the bubling sound.

              Comment


              • #8
                I'm using an AA batery cell, 1.5v.
                Any advice?

                Comment


                • #9
                  I was wondering if it might be possible to use food grade charcoal in place of nano-coated copper for gans production, etc. Anybody have any ideas?

                  Comment


                  • #10
                    Originally posted by Dan Derbick View Post
                    I was wondering if it might be possible to use food grade charcoal in place of nano-coated copper for gans production, etc. Anybody have any ideas?
                    Some people use a carbon electrode and apply power. Mr Keshe says that produces a matter-level gans. We need to be working with plasma-level gans, which needs the field interactions created by the nano-coated copper oxide plate and zinc plate in salt water. (CO2 gans as an example.)

                    Comment

                    Announcement

                    Collapse
                    No announcement yet.
                    Working...
                    X